wireless linux naum funfa nem f*** .... RESOLVIDO

Question

meu notebook tem a placa interna de wireless Broadcom...
instalei o ndiswrapper, o modulo sobe certinho... ai to usando esse script para funcionar o wireless:#!/bin/sh
modprobe ndiswrapper
ifconfig eth0 down
iwconfig wlan0 essid GRAVADOR
iwconfig wlan0 channel 11
iwconfig wlan0 mode Managed
iwconfig wlan0 key restricted 4CFC38ACE530B3E9EBFAD50453
ifconfig wlan0 up
ifconfig wlan0 192.168.2.3 netmask 255.255.255.0
route del default
route add default wlan0
route add default gw 192.168.2.1mas naum deu certo... ai olhei no site guiawd e alterei o arquivo ifcfg-wlan0 e deixei assim:DEVICE=wlan0
ONBOOT=yes
TYPE=Wireless
MODE=Managed
ESSID=GRAVADOR
CHANNEL=11
IPADDR=192.168.2.3
NETMASK=255.255.255.0
NETWORK=192.168.2.0
BROADCAST=192.168.2.255
GATEWAY=192.168.2.1
USERCTL=no
PEERDNS=no
IPV6INIT=no
RATE=Auto
HWADDR=mas tb naum funfo... o iwconfig tah assim:wlan0     IEEE 802.11g  ESSID:off/any  Nickname:NoteBook
          Mode:Managed  Frequency:2.462 GHz  Access Point: 00:00:00:00:00:00   
          Bit Rate=54 Mb/s   Tx-Power:25 dBm   
          RTS thr=2347 B   Fragment thr=2346 B   
          Encryption key:4CFC-38AC-E530-B3E9-EBFA-D504-53   Security mode:restricted
          Power Management:off
          Link Quality:100/100  Signal level:-10 dBm  Noise level:-256 dBm
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0eu usei o iwlist wlan0 scan e voltou isso:wlan0     Scan completed :
          Cell 01 - Address: 00:11:95:0B:F2:90
                    ESSID:GRAVADOR
                    Protocol:IEEE 802.11g
                    Mode:Managed
                    Frequency:2.462 GHz (Channel 11)
                    Quality:0/100  Signal level:-61 dBm  Noise level:-256 dBm
                    Encryption key:on
                    Bit Rate:1 Mb/s
                    Bit Rate:2 Mb/s
                    Bit Rate:5.5 Mb/s
                    Bit Rate:11 Mb/s
                    Bit Rate:6 Mb/s
                    Bit Rate:9 Mb/s
                    Bit Rate:12 Mb/s
                    Bit Rate:18 Mb/s
                    Bit Rate:24 Mb/s
                    Bit Rate:36 Mb/s
                    Bit Rate:48 Mb/s
                    Bit Rate:54 Mb/s
                    Extra:bcn_int=100
                    Extra:atim=0
                    (Unknown Wireless Token 0x8C05)
          Cell 02 - Address: 00:06:25:9A:34:2E
                    ESSID:linksys
                    Protocol:IEEE 802.11b
                    Mode:Managed
                    Frequency:2.437 GHz (Channel 6)
                    Quality:0/100  Signal level:-90 dBm  Noise level:-256 dBm
                    Encryption key:off
                    Bit Rate:1 Mb/s
                    Bit Rate:2 Mb/s
                    Bit Rate:5.5 Mb/s
                    Bit Rate:11 Mb/s
                    Extra:bcn_int=100
                    Extra:atim=0
                    (Unknown Wireless Token 0x8C05)minha rede eh o ESSID: GRAVADOR!!! num sei mas oq fazer... alguem pode me ajudar???

Answer

voce usa autenticacao ? qual?

Answer

Tente realizar cada passo desse script, via linha de comando e v&aacute; checando o resultado.
Talvez assim vo&ccedil;&ecirc; descubra onde est&aacute; acontecendo o problema.

Pelo que parece ele n&atilde;o est&aacute; conseguindo pegar as configura&ccedil;&otilde;es da rede Wireless.

Answer

[quote=deep]voce usa autenticacao ? qual?[/quote]sim, Wep 128 bits
[quote=babau]Tente realizar cada passo desse script, via linha de comando e v&aacute; checando o resultado.
Talvez assim vo&ccedil;&ecirc; descubra onde est&aacute; acontecendo o problema.[/quote]jah fiz passo-a-passo e mesmo assim nada!!!
estranho q ele pega as configura&ccedil;oes automaticamente da outra rede, mas naum tah alterando pra minha!!!

Answer

resolvi com esse Script:
#!/bin/sh

clear

printf Subindo o Modulo... 
if modprobe ndiswrapper; then
        printf OK 

else
        printf Falhou 

fi

printf ETH0 Down... 
if ifconfig eth0 down; then
        printf OK 

else
        printf Falhou 

fi

printf WLAN0 Down...
if ifconfig wlan0 down; then
        printf OK 

else
        printf Falhou 

fi

printf Setando o Mac do Access Point... 
if iwconfig wlan0 ap 00:11:95:0B:F2:90; then
        printf OK 

else
        printf Falhou 

fi

printf Setando o Channel... 
if iwconfig wlan0 channel 11; then
        printf OK 

else
        printf Falhou 

fi

printf Setando o Modo... 
if iwconfig wlan0 mode Managed; then
        printf OK 

else
        printf Falhou 

fi

printf Setando a Seguranca: 

printf      Encryptacao... 
if iwconfig wlan0 enc off; then
        printf OK 

else
        printf Falhou 

fi
printf      Chave Wep... 
if iwconfig wlan0 key open 4CFC38ACE530B3E9EBFAD50453; then
        printf OK 

else
        printf Falhou 

fi

printf Setando o ESSID... 
if iwconfig wlan0 essid GRAVADOR; then
        printf OK 

else
        printf Falhou 

fi

printf WLAN0 Up... 
if ifconfig wlan0 up; then
        printf OK 

else
        printf Falhou 

fi

printf Definindo o IP e Mascara... 
if ifconfig wlan0 192.168.2.3 netmask 255.255.255.0; then
        printf OK 

else
        printf Falhou 

fi

printf Configurando a Rota: 

#route del default
printf      Rota padrao... 
if route add default wlan0; then
        printf OK 

else
        printf Falhou 

fi
printf      Definindo Gateway... 
if route add default gw 192.168.2.1; then
        printf OK 

else
        printf Falhou 

fi

printf Setando o Nameserver... 
echo nameserver 24.153.22.67 > /etc/resolv.conf
if echo nameserver 24.153.23.66 >> /etc/resolv.conf; then
        printf OK 

else
        printf Falhou 

fi

iwconfig wlan0
ifconfig wlan0
route
if ping -c2 www.terra.com.br; then
        printf INTERNET UP... 

else
        printf Internet Down...

fi

Ferramentas

Mover Tópico