problema com ndiswrapper e placa broadcom integrada

Question

tenho um  notebook com o slack 10.2 instalado e a placa de rede wireless broadcom:
# lspci|grep Broadcom
00:0b.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02)
instalei o ndiswrapper 1.14 (foi o unico q compilou corretamente)
# ndiswrapper -l
Installed drivers:
bcmwl5          driver installed, hardware present
o modulo do ndiswrapper some normal:
# lsmod|grep ndis
ndiswrapper           152376   0
usbcore                59148   1  [ndiswrapper audio hid usbmouse snd-usb-audio snd-usb-lib usb-storage usb-ohci ehci-hcd]
mas a placa naum funciona d jeito nenhum:
# ifconfig
lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:221 errors:0 dropped:0 overruns:0 frame:0
          TX packets:221 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:17085 (16.6 Kb)  TX bytes:17085 (16.6 Kb)

wlan0     Link encap:Ethernet  HWaddr 00:14:A4:0E:C2:1C
          inet addr:192.168.2.3  Bcast:192.168.2.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
          Interrupt:4 Memory:e2000000-e2002000

root@acer:/home/mestre5/scripts# iwlist wlan0 scanning
wlan0     No scan results
alguem tem alguma ideia, as minhas jah acabaram???

Answer

sobe

Answer

Por incr&iacute;vel que pare&ccedil;a tive problemas em utilizar vers&otilde;es do ndiswrapper acima da 1.0

S&oacute; consegui fazer funcionar (inclusive compilar o m&oacute;dulo) com a vers&atilde;o 0.12.

Pode ser uma possibilidade.

Answer

[quote=babau]Por incr&iacute;vel que pare&ccedil;a tive problemas em utilizar vers&otilde;es do ndiswrapper acima da 1.0

S&oacute; consegui fazer funcionar...[/quote]mas vc usa o slack 10.2 ???
eu vou tentar e posto aki...

valew

Answer

[quote=babau]Por incr&iacute;vel que pare&ccedil;a tive problemas em utilizar vers&otilde;es do ndiswrapper acima da 1.0

S&oacute; consegui fazer funcionar...[/quote]naum funcionou....
# ndiswrapper -l
Installed ndis drivers:
bcmwl5  driver present, hardware present
# lsmod|grep ndiswrapper
ndiswrapper            79916   1
usbcore                59148   1  [ndiswrapper audio hid usbmouse snd-usb-audio snd-usb-lib usb-storage usb-ohci ehci-hcd]
# dmesg|grep ndiswrapper
ndiswrapper version 0.12 loaded (preempt=no,smp=no)
ndiswrapper: using irq 4
wlan0: ndiswrapper ethernet device 00:14:a4:0e:c2:1c using driver bcmwl5
ndiswrapper: driver bcmwl5 (Broadcom,12/22/2004, 3.100.46.0) added
# iwconfig
lo        no wireless extensions.

eth0      no wireless extensions.

wlan0     IEEE 802.11g  ESSID:off/any  Nickname:acer
          Mode:Managed  Frequency:2.412 GHz  Access Point: 00:00:00:00:00:00
          Bit Rate=54 Mb/s   Tx-Power:25 dBm
          RTS thr=2347 B   Fragment thr=2346 B
          Encryption key:off
          Power Management:off
          Link Quality:100/100  Signal level:-10 dBm  Noise level:-256 dBm
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0
# iwlist wlan0 scan
wlan0     No scan results

Answer

sobe

Ferramentas

Mover Tópico