Quando eu uso 'ifconfig' no inicio, está tudo bem..
root@null:~# ifconfig
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 10.0.0.106 netmask 255.255.255.0 broadcast 10.0.0.255
inet6 fe80::ea9a:8fff:fee3:fa38 prefixlen 64 scopeid 0x20<link>
ether e8:9a:8f:e3:fa:38 txqueuelen 1000 (Ethernet)
RX packets 14 bytes 1684 (1.6 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 22 bytes 1847 (1.8 KiB)
TX errors 0 dropped 0 overruns 0 carrier 1 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 0 (Loopback Local)
RX packets 20 bytes 1200 (1.1 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 20 bytes 1200 (1.1 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
wlan0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
ether 60:d8:19:5b:4f:d6 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
Certo, agora quando uso 'airmon-ng start wlan0' para iniciar uma rede monitor, acontece um erro...
root@null:~# airmon-ng start wlan0
Found 3 processes that could cause trouble.
If airodump-ng, aireplay-ng or airtun-ng stops working after
a short period of time, you may want to kill (some of) them!
PID Name
552 NetworkManager
626 wpa_supplicant
627 dhclient
PHY Interface Driver Chipset
phy0 wlan0 brcmsmac Broadcom on bcma bus, information limited
Newly created monitor mode interface wlan0mon is *NOT* in monitor mode.
Removing non-monitor wlan0mon interface...
WARNING: unable to start monitor mode, please run "airmon-ng check kill"Faço os passos corretamente como no vídeo, porém não consigo criar a rede monitor, e se eu utilizar o 'ifconfig' novamente, o wlan0 some.
root@null:~# ifconfig
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 10.0.0.106 netmask 255.255.255.0 broadcast 10.0.0.255
inet6 fe80::ea9a:8fff:fee3:fa38 prefixlen 64 scopeid 0x20<link>
ether e8:9a:8f:e3:fa:38 txqueuelen 1000 (Ethernet)
RX packets 5342 bytes 3689359 (3.5 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 5246 bytes 652624 (637.3 KiB)
TX errors 0 dropped 0 overruns 0 carrier 1 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 0 (Loopback Local)
RX packets 20 bytes 1200 (1.1 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 20 bytes 1200 (1.1 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
Poderiam me auxiliar? Obrigado.
