pereira.rr

Gente o Problema é o seguinte: Instalei o LInux Kurumim 4.0 (Kernel 2.6) em um HD Seagate Barracuda 40 GB, até ai tudo bem.
Tenho Também outra HD Seagate Barracuda Serial Ata 80Gb e o Linux não reconhce. (o duro ´que todos meus arquivos pessoais estão neste hd)

A contoloadora da Sata é na Ponte Sul. Driver sys

Aparece algo +- assim: Please Patiente ATA 1 is slow respond.

Segue ai meus Hardware.
Placa mãe : ABIT NF7 S2 Revisão 14 (já tentei com a 10, 11, 12, 13. Por isso acho que não é Bios)
Geforce fx 5200 128DDR
768DDr Samsung 400
Athlon XP 2000+

Por favor alguém ajuda ae.

__________________
Abit NF7 S2
Atlhon XP 2000+
HD 40 GB Seagate
HD 80 GB SATA Seagate
768 DDR 400 Sansung
GForce 4 MX 440
Home Theater Creative 6.1 Inspire 6.600

pereira.rr

Pô ninguém pode me ajudar?

__________________
Abit NF7 S2
Atlhon XP 2000+
HD 40 GB Seagate
HD 80 GB SATA Seagate
768 DDR 400 Sansung
GForce 4 MX 440
Home Theater Creative 6.1 Inspire 6.600

psi666

SATA é reconhecido como SCSI no Linux...

__________________
[]'s

Ricardo 'PSi666' Guimarães
http://www.eixodomal.com.br

Bruno Zilio

Aproveitando o topico..
Qual distro instalar em HD SATA ?
Acredito que somente o kernel 2.6 que reconhece assim de prima pra poder instalar no HD SATA sem precisar instalar em um PATA depois atualizar o kernel e depois copiar para o SATA...Certo ?

Quais distros eu consigo ?
Slackware 10 não reconheceu meu HD...(Postei uma vez achando que tinha reconhecido, mas me enganei !)

__________________
¬¬

pflynn

Bom, isso depende batante. Depende tanto da versão do kernel quanto do modelo do hardware. As controladoras da Silicon Image, por exemplo, umas das primeiras a serem suportadas pelo Linux (ainda na série 2.4) podem ser reconhecidas no 2.4 tanto quanto IDE ( CONFIG_BLK_DEV_SIIMAGE) como faz por exemplo o kernel padrão do Slackware 10, quanto SCSI (CONFIG_SCSI_SATA_SIL). Em versões mais recentes o suporte já e 100 % SATA.

__________________
------------------------------------------------
Muito bom. Mas tijolo não revida!
------------------------------------------------

none

vc sabe se ta habilitado o libsata ?

none

__________________
"We will call you Cygnus
The God of Balance you Shall be"

Só pq gostei destes emoticons !

pereira.rr

Olha o Kernel usado é o 2.6.8.1
Não sei se o Driver é Silicom Image ou Sis.
Só sei que durante o boot o sistema reconhece pois aparece a seguinte frase.

ATA 1 SLOW TO RESPOND. PATIENTE........

__________________
Abit NF7 S2
Atlhon XP 2000+
HD 40 GB Seagate
HD 80 GB SATA Seagate
768 DDR 400 Sansung
GForce 4 MX 440
Home Theater Creative 6.1 Inspire 6.600

pflynn

pereira.rr, tem como postar aqui a saída do dmesg ?

__________________
------------------------------------------------
Muito bom. Mas tijolo não revida!
------------------------------------------------

pereira.rr

Olha gente sou completamente leigo. Estou iniciando agora minha jornada no linux. Não sei o que é Libsata ou dmesg...
Sei algumas coisas apenas. Alias será que o Kurumin é a melhor distribuição para quem estrá iniciando??

O QUE É DMESG??
e OBRIGADO POR ENQUANTO PESSOAL..

__________________
Abit NF7 S2
Atlhon XP 2000+
HD 40 GB Seagate
HD 80 GB SATA Seagate
768 DDR 400 Sansung
GForce 4 MX 440
Home Theater Creative 6.1 Inspire 6.600

niTsumuji

Como root, digite dmesg. Vai aparecer um monte de coisa. É o resultado do boot. Copia, e cola aí pra nós!

__________________
Calma! Não tema! Com Slackware não há problema!

-----------------
Slackware 11.0
AMD Athlon64 3000+@1800
OpenGL Programmer
Assembler n00b

pereira.rr

blz.. Tai o resultado do boot...

errupt Link [LNK2] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 9 10 11 *12 14 15)
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [APC1] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs *17), disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs *18), disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs *19), disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21) *0, disabled.
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21) *0, disabled.
ACPI: PCI Interrupt Link [APCI] (IRQs 20 21) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21) *0, disabled.
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs *23), disabled.
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21) *0, disabled.
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21) *0, disabled.
ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 22) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
ACPI: PCI Interrupt Link [LSMB] enabled at IRQ 10
ACPI: PCI interrupt 0000:00:01.1[A] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LUBA] enabled at IRQ 3
ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 3 (level, low) -> IRQ 3
ACPI: PCI Interrupt Link [LUBB] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:02.1[b] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 9
ACPI: PCI interrupt 0000:00:02.2[C] -> GSI 9 (level, low) -> IRQ 9
ACPI: PCI Interrupt Link [LACI] enabled at IRQ 5
ACPI: PCI interrupt 0000:00:06.0[A] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI Interrupt Link [LSID] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:0b.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNK4] enabled at IRQ 10
ACPI: PCI interrupt 0000:02:07.0[A] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LNK3] enabled at IRQ 12
ACPI: PCI interrupt 0000:02:0b.0[A] -> GSI 12 (level, low) -> IRQ 12
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 10 (level, low) -> IRQ 10
TC classifier action (bugs to netdev@oss.sgi.com cc hadi@cyberus.ca)
vesafb: framebuffer at 0xd8000000, mapped to 0xf0809000, size 1875k
vesafb: mode is 800x600x16, linelength=1600, pages=2
vesafb: protected mode interface info at c000:f1f0
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
fb0: VESA VGA frame buffer device
Machine check exception polling timer started.
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
bootsplash 3.1.4-2004/02/19-spock-0.1: looking for picture.... found (800x600, 1
5103 bytes, v3).
Console: switching to colour frame buffer device 90x17
Generic RTC Driver v1.07
Using anticipatory io scheduler
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: AES key scrubbing enabled
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE2-U400R: IDE controller at PCI slot 0000:00:09.0
NFORCE2-U400R: chipset revision 163
NFORCE2-U400R: not 100% native mode: will probe irqs later
NFORCE2-U400R: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE2-U400R: 0000:00:09.0 (rev a3) UDMA133 controller
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hdaMA, hdbMA
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdcMA, hddMA
hda: ST340017A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: HL-DT-ST GCE-8523B, ATAPI CD/DVD-ROM drive
hdd: HL-DT-STDVD-ROM GDR8161B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 78165360 sectors (40020 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
hda: hda2 < hda5 hda6 hda7 >
hdc: ATAPI 52X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 48X DVD-ROM drive, 256kB Cache, UDMA(33)
3ware Storage Controller device driver for Linux v1.26.00.039.
3w-xxxx: No cards found.
3ware 9000 Storage Controller device driver for Linux v2.26.02.001.
libata version 1.02 loaded.
sata_nv version 0.02
ACPI: PCI interrupt 0000:00:0b.0[A] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:0b.0 to 64
ata1: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xCC00 irq 11
ata2: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xCC08 irq 11
ata1 is slow to respond, please be patient
ata1 failed to respond (30 secs)
scsi0 : sata_nv
ata2: no device found (phy stat 00000000)
scsi1 : sata_nv
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid5 personality registered as nr 4
raid5: automatically using best checksumming function: pIII_sse
pIII_sse : 4668.000 MB/sec
raid5: using function: pIII_sse (4668.000 MB/sec)
raid6: int32x1 632 MB/s
raid6: int32x2 800 MB/s
raid6: int32x4 480 MB/s
raid6: int32x8 472 MB/s
raid6: mmxx1 1390 MB/s
raid6: mmxx2 2464 MB/s
raid6: sse1x1 1292 MB/s
raid6: sse1x2 2210 MB/s
raid6: using algorithm sse1x2 (2210 MB/s)
md: raid6 personality registered as nr 8
md: multipath personality registered as nr 7
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm@uk.sistina.com
EISA: Probing bus 0 at eisa0
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 1
PM: Reading pmdisk image.
PM: Resume from disk failed.
ACPI: (supports S0 S1 S4 S5)
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Couldn't find valid RAM disk image starting at 0.
ReiserFS: hda5: found reiserfs format "3.6" with standard journal
ReiserFS: hda5: using ordered data mode
ReiserFS: hda5: journal params: device hda5, size 8192, journal first block 18,
max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda5: checking transaction log (hda5)
ReiserFS: hda5: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 260k freed
Adding 2048248k swap on /dev/hda6. Priority:-1 extents:1
Serial: 8250/16550 driver $Revision: 1.90 $ 14 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1: LSR safety check engaged!
ttyS1: LSR safety check engaged!
NTFS driver 2.1.15 [Flags: R/W MODULE].
NTFS-fs warning (device hda7): ntfs_fill_super(): Atime updates are not implemen
ted yet. Disabling them.
NTFS volume version 3.1.
warning: process `update' used the obsolete bdflush system call
Fix your initscripts?
ttyS1: LSR safety check engaged!
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
parport0: irq 7 detected
via-rhine.c:v1.10-LK1.1.20-2.6 May-23-2004 Written by Donald Becker
ACPI: PCI interrupt 0000:02:0b.0[A] -> GSI 12 (level, low) -> IRQ 12
eth0: VIA Rhine III at 0xe8001000, 00:50:8d:5f:fc:d5, IRQ 12.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 41e1.
8139too Fast Ethernet driver 0.9.27
ACPI: PCI interrupt 0000:02:07.0[A] -> GSI 10 (level, low) -> IRQ 10
eth1: RealTek RTL8139 at 0xf0cff000, 00:e0:7d:c5:8a:76, IRQ 10
eth1: Identified 8139 chip type 'RTL-8139C'
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected NVIDIA nForce2 chipset
agpgart: Maximum main memory to use for agp memory: 690M
agpgart: AGP aperture is 128M @ 0xe0000000
via-rhine.c:v1.10-LK1.1.20-2.6 May-23-2004 Written by Donald Becker
ACPI: PCI interrupt 0000:02:0b.0[A] -> GSI 12 (level, low) -> IRQ 12
eth0: VIA Rhine III at 0xe8001000, 00:50:8d:5f:fc:d5, IRQ 12.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 41e1.
8139too Fast Ethernet driver 0.9.27
ACPI: PCI interrupt 0000:02:07.0[A] -> GSI 10 (level, low) -> IRQ 10
eth1: RealTek RTL8139 at 0xf0d6a000, 00:e0:7d:c5:8a:76, IRQ 10
eth1: Identified 8139 chip type 'RTL-8139C'
ACPI: PCI interrupt 0000:00:06.0[A] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:06.0 to 64
intel8x0_measure_ac97_clock: measured 49529 usecs
intel8x0: clocking to 47390
ACPI: PCI interrupt 0000:02:07.0[A] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI interrupt 0000:02:0b.0[A] -> GSI 12 (level, low) -> IRQ 12
sk98lin: No adapter found.
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
ACPI: Processor [CPU0] (supports C1)
ACPI: Power Button (FF) [PWRF]
ACPI: Fan [FAN] (on)
ACPI: Thermal Zone [THRM] (45 C)
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: overridden by ACPI.
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: overridden by ACPI.
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 10 (level, low) -> IRQ 10
NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-6111 Tue Jul 27 07:55:
38 PDT 2004
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
usbcore: registered new driver usbfs
usbcore: registered new driver hub
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
parport0: irq 7 detected
lp0: using parport0 (polling).
lp0: console ready
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
NET: Registered protocol family 17
NET: Registered protocol family 10
Disabled Privacy Extensions on device c0456d20(lo)
IPv6 over IPv4 tunneling driver
eth0: Setting full-duplex based on MII #1 link partner capability of 41e1.
NET: Registered protocol family 24
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (6143 buckets, 49144 max) - 296 bytes per conntrack
eth0: no IPv6 routers present
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 3 (level, low) -> IRQ 3
ohci_hcd 0000:00:02.0: PCI device 10de:0087 (nVidia Corporation)
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: irq 3, pci mem f0e30000
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
ACPI: PCI interrupt 0000:00:02.1[b] -> GSI 11 (level, low) -> IRQ 11
ohci_hcd 0000:00:02.1: PCI device 10de:0087 (nVidia Corporation)
PCI: Setting latency timer of device 0000:00:02.1 to 64
ohci_hcd 0000:00:02.1: irq 11, pci mem f0e32000
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
usb 1-1: new full speed USB device using address 2
usb 2-1: new full speed USB device using address 2
usb 2-2: new low speed USB device using address 3
usb 2-3: new low speed USB device using address 4
Linux video capture interface: v1.00
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 2 if 0 alt 0 pr
oto 2 vid 0x03F0 pid 0x7104
/home/kurumin/tmp/spca5xx-20041210/drivers/usb/spca50x.c: USB SPCA5XX camera fou
nd. Type Vimicro Zc301+pb0330
/home/kurumin/tmp/spca5xx-20041210/drivers/usb/spca50x.c: [spca50x_probe:7663] C
amera type JPEG
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
usbcore: registered new driver spca50x
/home/kurumin/tmp/spca5xx-20041210/drivers/usb/spca50x.c: spca5xx driver 0.54 re
gistered
usbcore: registered new driver hiddev
drivers/usb/input/hid-core.c: ctrl urb status -32 received
drivers/usb/input/hid-core.c: ctrl urb status -32 received
input: USB HID v1.10 Mouse [PS/2+USB Mouse] on usb-0000:00:02.1-2
input: USB HID v1.10 Joystick [DragonRise Inc. Generic USB Joystick ] on u
sb-0000:00:02.1-3
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
ts: Compaq touchscreen protocol output
ACPI: PCI interrupt 0000:00:02.2[C] -> GSI 9 (level, low) -> IRQ 9
ehci_hcd 0000:00:02.2: PCI device 10de:0088 (nVidia Corporation)
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: irq 9, pci mem f0e56000
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 3
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
usb 2-1: USB disconnect, address 2
drivers/usb/class/usblp.c: usblp0: removed
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 8 ports detected
usb 2-2: USB disconnect, address 3
usb 2-3: USB disconnect, address 4
usb 1-1: USB disconnect, address 2
ohci_hcd 0000:00:02.1: wakeup
usb 1-1: new full speed USB device using address 3
/home/kurumin/tmp/spca5xx-20041210/drivers/usb/spca50x.c: USB SPCA5XX camera found. Type Vimicro Zc301+pb0330
/home/kurumin/tmp/spca5xx-20041210/drivers/usb/spca50x.c: [spca50x_probe:7663] Camera type JPEG
usb 2-1: new full speed USB device using address 5
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 5 if 0 alt 0 proto 2 vid 0x03F0 pid 0x7104
usb 2-2: new low speed USB device using address 6
drivers/usb/input/hid-core.c: ctrl urb status -32 received
drivers/usb/input/hid-core.c: ctrl urb status -32 received
input: USB HID v1.10 Mouse [PS/2+USB Mouse] on usb-0000:00:02.1-2
usb 2-3: new low speed USB device using address 7
input: USB HID v1.10 Joystick [DragonRise Inc. Generic USB Joystick ] on usb-0000:00:02.1-3
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
pciehp: PCI Express Hot Plug Controller Driver version: 0.4
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
root@Servidor:~#


[/img]

__________________
Abit NF7 S2
Atlhon XP 2000+
HD 40 GB Seagate
HD 80 GB SATA Seagate
768 DDR 400 Sansung
GForce 4 MX 440
Home Theater Creative 6.1 Inspire 6.600

pflynn

Só mais uma coisa:
O que você tem nesse arquivo: /proc/scsi/scsi ?

cat /proc/scsi/scsi

__________________
------------------------------------------------
Muito bom. Mas tijolo não revida!
------------------------------------------------

pereira.rr

seria este file:/proc/scsi/. ai tem uma pasta com o nome sg então fica assim: file:/proc/scsi/sg e dentro desta pasta tem arquivos com estes nomes abaixo
ALLO DIO
DEBUG
DEF_RESERVED_SIZE
DEVICE HDR
DEVICES
DEVICE STRS
VERSION

__________________
Abit NF7 S2
Atlhon XP 2000+
HD 40 GB Seagate
HD 80 GB SATA Seagate
768 DDR 400 Sansung
GForce 4 MX 440
Home Theater Creative 6.1 Inspire 6.600

pereira.rr

file:/home/kurumin/Downloads neste diretório esta o driver NFORCE-Linux-x86-1.0-0292-pkg1.run, que é o driver Nfoce para linux para placas mães que usasm este driver.
Como faço para instalá-lo. Em que pasta tenho que deixa-lo pra instalá-lo?.. quem sabe instalando ele não resolva alguma coisa.?????

__________________
Abit NF7 S2
Atlhon XP 2000+
HD 40 GB Seagate
HD 80 GB SATA Seagate
768 DDR 400 Sansung
GForce 4 MX 440
Home Theater Creative 6.1 Inspire 6.600

niTsumuji

só executá-lo. Para isso, como root: chmod 755 NFORCE-Linux-x86-1.0-0292-pkg1.run
./NFORCE-Linux-x86-1.0-0292-pkg1.run
Isso vai fazê-lo executar.

__________________
Calma! Não tema! Com Slackware não há problema!

-----------------
Slackware 11.0
AMD Athlon64 3000+@1800
OpenGL Programmer
Assembler n00b

pereira.rr

mas eu deixo ele no diretório que está mesmo?

Como especifico onde ele esta. apenas aplicando este comando ele ja acha o driver e executá-o??

__________________
Abit NF7 S2
Atlhon XP 2000+
HD 40 GB Seagate
HD 80 GB SATA Seagate
768 DDR 400 Sansung
GForce 4 MX 440
Home Theater Creative 6.1 Inspire 6.600

bhzbaraka

Kra minha placa é igual a sua e naum tenho nenhum problema desse tipo... Minha BIOS é a 25 e acho que pode ser sua bios sim ...
Olha no site da Abit USA, que la tem todas as bios..


bhzbaraka.

__________________
Linux user # 375914.
http://counter.li.org/
www.fedora.org.br
_________________
Abit NF7-S Rev 2.0|Athlon XP3000+1GB Dual DDR400 Corsair Value Select|Radeon 9600XT 128MB |Seagate Barracuda 80 GB SATA 7.200 rpm|Maxtor 9 Plux 80 Gb 7.200 rpm|

pereira.rr

Achoi que a sua placa seria a NF7 S v2.0. Esta placa é diferente apesar de ter o nome parecido, pois para o meu modelo vai até o bios 14.
Já vi até no site da Global da Abit.

__________________
Abit NF7 S2
Atlhon XP 2000+
HD 40 GB Seagate
HD 80 GB SATA Seagate
768 DDR 400 Sansung
GForce 4 MX 440
Home Theater Creative 6.1 Inspire 6.600

pereira.rr

enfim então não tem solução mesmo?
com todos estes dados que passei ainda assim não épossível saber o que está acontecendo?

sera que seu eu tentar instalar o slack ou o red hat mudaria alguma coisa?

Mas tocando na mesma tecla ele chega a reconhecer o hd pois ele etá instaldo na entrada sata 1. O linux e reconhece mas aparece a seguinte frase.

SATA 1 SLOW TO RESPOND. PLEASE PATIENTE........

RECONHECER ELE RECONHECE MAS PORQUE NÃO RESPONDE????????

__________________
Abit NF7 S2
Atlhon XP 2000+
HD 40 GB Seagate
HD 80 GB SATA Seagate
768 DDR 400 Sansung
GForce 4 MX 440
Home Theater Creative 6.1 Inspire 6.600

MD5

Veja se isto pode ajuda-lo:
www.vivaolinux.com.br/artigos/verArtigo.php?codigo=1387&pagina=1

Se for para recomendar distro com maior probabilidade
de reconhecer seu disco, eu tentaria Suse ou Fedora. 8)
-------------------------------------------------------------------------